SD101201 Sensors
Description
Has two Hall Effect sensors; one detects speed and the other detects direction of movement of gear teeth. The outputs are open collector transistors. The Speed output goes high (on) when sensing the leading edge of a tooth and low (off) on the trailing edge of the tooth when run against a standard target. The direction of movement is latched on the leading edge of the speed sensor; the Direction output goes high for clockwise rotation and low for counterclockwise rotation. The state of the Direction output always leads the rising edge of the speed outputFeatures
- Separate digital outputs for speed and direction
- From near zero speed up to 15 kHz sensing capability
- Plastic flange-mount sensor rated to 125 ⁰C
- RoHS compliant
- IP67
- Typical air gap of 1.5 mm (0.06”)*
Application
- Wheel speed and direction
- Hoist speed and direction
- Transmission speed and direction
- Industrial feedback and control
- Hoist speed and direction
Preferred Parts
Swipe to Browse
| Part Number | Check Stock | Termination | Data | CAD |
|---|---|---|---|---|
|
SD101201 |
Delphi Metri-Pack 150 connector |
It is the responsibility of the user to determine product suitability. Specifications are subject to change without notice.
*Actuator length based on distance from pivot point
Related Products
E-Bike Sensor
- Supply voltage: 6.5 – 20 VDC
- Signal Output low: 7+1.4/-1.1 mA
- Signal Output high: 14+2.8/-2.2 mA
- Operating frequency: 1 – 2.5 kHz
- Operating temperature: -25°C – 85°C
LIN Sensors – Kit with magnet
- Easy setup and robust monitoring with M4 screws
- Dual independent (redundant) outputs assure high reliability
- No mechanical interface means no parts to wear out or jam
- Comes with 20 AWG 305 mm (12”) discrete wire leads or harness with connector
- RoHS compliant
- IP68*
- Compliant to industrial/automotive EMC/EMI/ESD directives
ANG Sensors
- Angular position sensor with high tolerance for misalignment
- Non-contact angular position sensing and full 360O rotation
- Custom programming available for: angle range, slope, PWM output – contact factory
- No mechanical interface means no parts to wear out or jam
- Comes with 20 AWG 305 mm (12”) discrete wire leads
- RoHS Compliant
- IP68*
- Maximum air gap of 6 mm (0.24”)
- Compliant to industrial/automotive EMC/EMI/ESD directives
Speed & Direction Sensor Kit
- Capable of measuring from near zero up to 20 KHz.
- Variable shaft length (20 to 80 mm)
- Variable shaft diameter (12 to 20 mm)
- 2-wire, 3-wire, 4-wire output
- Cable interface (connector upon request)
- Rotatable shaft head (to determine angle of wire outlet)
- Flexible wire orientation (horizontal or right-angle)
- Wire harness option with customer-specific connector (available on request)
- Available with open-collector, PWM or Current signal outputs
AN1 Sensors
- Patented intrinsically linear angle position sensor (ILAPS)
- Magnet/sensor orientation provides linear output from 5⁰ to 85⁰ of rotation without the need for electrical compensation
- Return spring provides resistance to CCW motion
- Fully encapsulated electronics
- RoHS compliant
- IP67
AN8 Sensors
- Angular position sensor with high tolerance for misalignment
- Non-contact angular position sensing and full 360⁰ rotation
- Custom programming available for: angle range, slope, PWM output, custom magnets – contact factory
- No mechanical interface means no parts to wear out or jam
- Available with Delphi connector or 12” (305 mm) wire leads
- RoHS compliant
- IP67
- Maximum air gap of 5.5 mm (0.22”)*
AN9 Sensors
- Angular position sensor with high tolerance for misalignment
- Non-contact angular position sensing and full 360⁰ rotation
- Dual independent (redundant) outputs assure high reliability
- Custom programming available for: angle range, slope, PWM output, custom magnets - contact factory
- No mechanical interface means no parts to wear out or jam
- Comes with 18 AWG 305 mm (12”) wire leads
- RoHS Compliant
- IP68*
- Maximum air gap of 5.5 mm (0.22”)**
GS1001 – GS1002 Sensors
- From near zero speed up to 15 kHz sensing capability
- 10 bit dynamic threshold direction offers:
- – Automatically adjusting magnetic range
- – Self-compensating to target geometry
- Compatible with unregulated power supply
- RoHS compliant
- IP67
- Typical air gap of 1.5 mm*
GS1005 – GS1007 Sensors
- From near zero speed up to 15 kHz sensing capability
- 10 bit dynamic threshold direction offers:
- – Automatically adjusting magnetic range
- – Self-compensating to target geometry
- Compatible with unregulated power supply
- ROHS compliant
- IP67
- Typical air gap of 1.5 mm*
GS101201 – GS101202
- From near zero speed up to 15 kHz sensing capability
- Plastic flange-mount housing
- Compatible with unregulated power supply
- ROHS compliant
- IP67
- Typical air gap of 1.5 mm*
GS101205 Sensors
- From near zero speed up to 15 kHz sensing capability
- Plastic flange-mount housing
- Resistant to fuels, solvents, and lubricants associated with engines, transmissions, brakes and chassis systems
- ROHS compliant
- IP67
- Typical air gap of 1.5 mm*
GS102301 Sensors
- From near zero speed up to 15 kHz sensing capability
- Resistant to fuels, solvents, and lubricants associated with engines, transmissions, brakes and chassis systems
- Supplied with installed Viton O-ring
- Installs into a standard M20 X 1.5 O-ring port
- ROHS compliant
- IP67
- Typical air gap of 1.5 mm*
Distributor Stock Check.
Search our established network of franchised distributors and representatives
